RIT Coatings

Coating Solutions for Asset Preservation and Energy Conservation

SP Texture Coating®

Other Products
Technical Specs, Application
Instructions and SDS Info
DESCRIPTION

SP TEXTURE COAT is a mixture of high-performance ceramics and acrylics specially blended for breathability, adhesion, flexibility, and toughness. Additional lightweight aggregate compound is added into the formulation to insure a texture yet having added characteristics not found in standard dry mix ratios of stucco. SP TEXTURE is tested to show a low permeability and is not affected by water or moisture-penetration. It is designed to stay down for a long bonding life. It will not crack and peel. It is UV-protected for long life and durability against weathering whether in hot or cool climates, or whether in high humidity or very dry environments.

SP TEXTURE COAT was designed to coat a variety of surface structures on metal, wood, stone, concrete, fiberglass or composites. SP TEXTURE COAT breathes, and unlike standard stucco, can flex with the substrate without cracking, giving years of maintenance-free service. SP TEXTURE COAT will not allow water to penetrate and damage substrates. It has a mildew resistant agent in the formula to guard against the growth of mold and mildew. When top-coated with SUPER THERM to guard against solar radiation heat absorption, the system created provides an insulating effectiveness on exterior walls and will not detract from the texturing.

Surfaces must be clean and dry before application. Any loose or flaking old paints or corrosion must be removed from the surfaces before applying. Pressure-wash is done if possible to remove grease, oil, waxy substances, dirt, salts, etc. SP TEXTURE COAT can be applied by trowel or a Graco GTX 2000EX.

MINIMUM SPREAD RATE
For Smooth Finish – Apply 1 coat of SP TEXTURE COAT to smooth, sealed surface @ 30 sq ft/gallon; (2.8 sqmtr/gallon); 54 mils wet / 42 mils dry (1350 microns wet / 1050 microns dry).
For Textured Finish – Apply in 2 coats; Refer to SP TEXTURE COAT Application Sheet for instructions.
NOTE: Surface and ambient temperatures, as well as wind and humidity will influence and dictate cure-time.
Clean up: Soap and water for both person and equipment

  • Solids: White – By weight: 69% / By volume: 77.8%
  • 1-3 hours to tack free at 70°F (21°C)
  • 2nd coat of SP CERAMIC STUCCO window is 24 hours or less at 70°F (21°C)
  • SP TEXTURE COAT must be cured before applying SUPER THERM or any other top coat.
  • Lead- and Chromate-free
  • Cures By: Evaporation
  • Reacted Weight: 13.4 lbs/gallon
  • Shelf Life: Up to 2 years unopened under appropriate storage conditions (See MSDS)
  • VOC – 1.16 lbs/gal;124 grams per liter
  • Tinting: Can be tinted any color for additional fee.
  • Maximum Surface Temperature when applying; 150°F (65°C).
  • Minimum Surface Temperature when applying; 50°F (10°C).
  • Maximum Surface Temperature after curing; 200°F (93°C)

Do not use this product without first taking all appropriate safety measures to prevent property damage and injuries. These measures may include, without limitation: proper ventilation, use of proper lamps, wearing of protective clothing and masks, tenting, and proper separation of application areas. This coating is flammable. Keep away from flame, fire, or other sources of ignition. For more safety procedures, please refer to the SP Texture Coat Safety Data Sheet. KEEP OUT OF REACH OF CHILDREN.

Other Products
Technical Specs, Application
Instructions and SDS Info
DESCRIPTION

SP TEXTURE COAT is a mixture of high-performance ceramics and acrylics specially blended for breathability, adhesion, flexibility, and toughness. Additional lightweight aggregate compound is added into the formulation to insure a texture yet having added characteristics not found in standard dry mix ratios of stucco. SP TEXTURE is tested to show a low permeability and is not affected by water or moisture-penetration. It is designed to stay down for a long bonding life. It will not crack and peel. It is UV-protected for long life and durability against weathering whether in hot or cool climates, or whether in high humidity or very dry environments.

SP TEXTURE COAT was designed to coat a variety of surface structures on metal, wood, stone, concrete, fiberglass or composites. SP TEXTURE COAT breathes, and unlike standard stucco, can flex with the substrate without cracking, giving years of maintenance-free service. SP TEXTURE COAT will not allow water to penetrate and damage substrates. It has a mildew resistant agent in the formula to guard against the growth of mold and mildew. When top-coated with SUPER THERM to guard against solar radiation heat absorption, the system created provides an insulating effectiveness on exterior walls and will not detract from the texturing.

Surfaces must be clean and dry before application. Any loose or flaking old paints or corrosion must be removed from the surfaces before applying. Pressure-wash is done if possible to remove grease, oil, waxy substances, dirt, salts, etc. SP TEXTURE COAT can be applied by trowel or a Graco GTX 2000EX.

MINIMUM SPREAD RATE
For Smooth Finish – Apply 1 coat of SP TEXTURE COAT to smooth, sealed surface @ 30 sq ft/gallon; (2.8 sqmtr/gallon); 54 mils wet / 42 mils dry (1350 microns wet / 1050 microns dry).
For Textured Finish – Apply in 2 coats; Refer to SP TEXTURE COAT Application Sheet for instructions.
NOTE: Surface and ambient temperatures, as well as wind and humidity will influence and dictate cure-time.
Clean up: Soap and water for both person and equipment

  • Solids: White – By weight: 69% / By volume: 77.8%
  • 1-3 hours to tack free at 70°F (21°C)
  • 2nd coat of SP CERAMIC STUCCO window is 24 hours or less at 70°F (21°C)
  • SP TEXTURE COAT must be cured before applying SUPER THERM or any other top coat.
  • Lead- and Chromate-free
  • Cures By: Evaporation
  • Reacted Weight: 13.4 lbs/gallon
  • Shelf Life: Up to 2 years unopened under appropriate storage conditions (See MSDS)
  • VOC – 1.16 lbs/gal;124 grams per liter
  • Tinting: Can be tinted any color for additional fee.
  • Maximum Surface Temperature when applying; 150°F (65°C).
  • Minimum Surface Temperature when applying; 50°F (10°C).
  • Maximum Surface Temperature after curing; 200°F (93°C)

Do not use this product without first taking all appropriate safety measures to prevent property damage and injuries. These measures may include, without limitation: proper ventilation, use of proper lamps, wearing of protective clothing and masks, tenting, and proper separation of application areas. This coating is flammable. Keep away from flame, fire, or other sources of ignition. For more safety procedures, please refer to the SP Texture Coat Safety Data Sheet. KEEP OUT OF REACH OF CHILDREN.